If Cricut Design Space reports that it cannot read the registration marks on glossy paper, check the printed border and reduce glare before recalibrating. This five-step guide is for Cricut users whose Print Then Cut sheet fails during scanning; it helps you identify whether the marks are intact and choose a practical fix. Cricut says reflective and glossy materials can interfere with the sensor, and that Print Then Cut works best with non-reflective materials.
Prerequisites
- Materials: Your printed project sheet, cutting mat, Cricut machine, and Design Space. Have matte transparent tape available if you want to try the glare-reduction method.
- Time: Allow about 10–20 minutes to inspect, reprint or adjust the sheet, and run a small test. This is an estimate; printer setup and repeated scans can take longer.
- Difficulty: Easy.
How to Check the Registration Marks
Step 1: Confirm the sheet is a Print Then Cut print
In Design Space, reopen the project and use its Print Then Cut workflow to send a fresh sheet to your printer. Registration marks are the dark sensor border printed around the design area; they give the machine a reference for locating the printed artwork. Do not use a screenshot, photocopy, or resized image of a previous sheet, because changing its scale or layout can change the marks’ relationship to the artwork.
Use the printer’s system dialog if needed to check that the page size and orientation match the material you selected. Cricut’s guidance says the printed sheet should show four sensor marks and retain at least 1/2 inch (1.25 cm) between the marks and the material edges. Follow the on-screen layout for your specific machine and sheet size. Cricut’s Print Then Cut instructions explain the expected print layout.
Step 2: Inspect each mark under even light
Before loading the mat, check all four corners. Each mark should be dark, complete, and easy to distinguish from the paper. Look for a clipped corner, smudged ink, a crease, a label or tape crossing the line, or a design pattern that runs into the sensor area. Tilt the sheet under a lamp: a bright reflection that washes over a mark can make the black border hard for the sensor to see.
Also check that the sheet is flat and that its printed edges are not curled. If a mark is incomplete or blurred, print the project again rather than trying to draw over the mark. Keep the sheet’s scale unchanged.
Step 3: Reduce glare or switch to matte material
The most reliable fix is to reprint on compatible, non-reflective paper. Cricut’s compatibility guidance says glossy, metallic, glitter, and other reflective finishes are not supported because they may prevent the sensor from reading the marks or lead to cuts offset from the printed design. Compatibility also varies by machine: Explore Air 2 and older models are limited to non-reflective white materials; newer listed models can use non-reflective white, lightly colored, and simple patterned materials. Check the current Print Then Cut compatible materials guide for your machine.
If you need to try the glossy sheet, Cricut suggests that matte transparent tape over the sensor marks may reduce glare. Apply a small, smooth piece over each mark without bubbles or wrinkles, then inspect that the black line remains visible through it. Treat this as a troubleshooting attempt, not a guarantee that glossy material will work on every machine or paper.
Step 4: Load the sheet in the correct orientation
Place the printed sheet on the mat in the position shown in Design Space. For most Cricut smart cutting machines, Cricut’s calibration guidance specifies the top-left corner; Cricut Venture uses the bottom-left corner. If you use A4 material, follow the on-screen orientation notes, since the long edge may need to run horizontally. Press the sheet flat and make sure it has not shifted relative to the mat.
Move direct sunlight or a bright lamp away from the sensor area while scanning. Keep the space around the marks clear so nothing casts a sharp shadow onto them.
Step 5: Test, then calibrate only if the scan or cut still needs it
Run a small Print Then Cut test using the same material and settings. If the machine reads the marks but the cut is consistently misaligned, run Print Then Cut calibration in Design Space using the calibration sheet and instructions for your machine. Calibration adjusts cut alignment; it does not make reflective paper compatible or repair a missing printed mark. Cricut’s calibration guide specifies white, non-textured copy paper for the calibration sheet and provides device-specific placement steps.
Troubleshooting
- The machine stops before scanning: Check that the sheet is oriented as Design Space shows, lies flat, and has all four visible marks. Reprint if ink is faint, smeared, clipped, or covered.
- The sensor still cannot read a taped mark: Remove glare from nearby lights and check that the tape is matte and transparent, with no bubbles or folds over the mark. If the scan still fails, move to matte, non-reflective paper; tape is only a possible aid for glossy material.
- The scan succeeds but cuts are offset: First verify that the print was not resized and that the correct material size was used. Then calibrate with the official sheet and follow the prompts. Calibration is for alignment after the sensor can read the page.
Frequently Asked Questions
Can Cricut Print Then Cut on glossy sticker paper?
Glossy and reflective finishes are not supported in Cricut’s compatibility guidance because reflections can interfere with mark detection or cut alignment. A matte paper is the more dependable choice.
Will transparent tape always fix a glossy-paper calibration error?
No. Cricut says matte transparent tape over the marks may reduce glare and improve results, but the material remains reflective and success can vary. If the machine still cannot scan the marks, use non-reflective material.
Should I recalibrate whenever Cricut cannot read the marks?
Not as the first fix. Check the print, orientation, and glare first. Calibration addresses cut alignment; it cannot restore a mark the sensor cannot see. Use Cricut’s current calibration steps if the machine reads the sheet but cuts inaccurately.
Sources: Cricut Help Center, Machine cannot read the cut sensor marks; Print Then Cut compatible materials; and calibration instructions, accessed November 20, 2026.